How do I get out of utility mode in BIOS?

How do I exit BIOS utility?

Press F10 to save and exit BIOS.

How do I turn off UEFI setup utility?

The Fn keys can be used to issue commands to the UEFI (BIOS). Try pressing F1 and see if it brings up a list of Fn associated commands. Look for “Quit Without Saving Changes”, and press that Fn key. That should get you out of the UEFI and force a re-boot.

How do I get out of UEFI BIOS?

Press the F10 key. You then might get a confirmation to exit BIOS.

How do I exit aptio setup utility?

Select the Security menu n the Aptio setup utility, select ‘secure Boot Control’ and change to disable. Select Save & Exit and press ‘yes’. Hold down the power button until the unit switches power off completely.

How do I fix BIOS not booting?

If you cannot enter the BIOS setup during boot, follow these steps to clear the CMOS:

  1. Turn off all peripheral devices connected to the computer.
  2. Disconnect the power cord from the AC power source.
  3. Remove the computer cover.
  4. Find the battery on the board. …
  5. Wait one hour, then reconnect the battery.

How do I fix BIOS boot loop?

Unplug power cable from PSU. Press the power button for 20 seconds. Remove the CMOS battery and wait 5 minutes and insert CMOS battery back. Make sure to connect only the disk where Windows was installed…if you installed Windows while having only one disk on your PC.

How do I get out of UEFI BIOS utility EZ mode?

Try the following and see if it resolves the problem:

  1. In the Aptio Setup Utility, select the “boot” menu and then select “Launch CSM” and change it to “enable”.
  2. Next select the “Security” menu and then select “secure Boot Control” and change to “disable”.
  3. Now select “Save & Exit” and press “yes”.

19 сент. 2019 г.

How do I adjust BIOS settings?

How to Configure the BIOS Using the BIOS Setup Utility

  1. Enter the BIOS Setup Utility by pressing the F2 key while the system is performing the power-on self-test (POST). …
  2. Use the following keyboard keys to navigate the BIOS Setup Utility: …
  3. Navigate to the item to be modified. …
  4. Press Enter to select the item. …
  5. Use the up or down arrow keys or the + or – keys to change a field.

What is UEFI setup utility?

UEFI is essentially a tiny operating system that runs on top of the PC’s firmware, and it can do a lot more than a BIOS. It may be stored in flash memory on the motherboard, or it may be loaded from a hard drive or network share at boot.

Why does computer go straight to BIOS?

Windows 10 users reported an issue when booting their computers. Instead of getting to the Windows loading screen, the PC boots directly into the BIOS. This unusual behavior could be triggered by different causes: recently changed/added hardware, hardware damage, improper hardware connections, and other issues.

How do I reset my BIOS to default?

Reset the BIOS to Default Settings (BIOS)

  1. Access the BIOS Setup utility. See Accessing BIOS.
  2. Press the F9 key to automatically load the factory default settings. …
  3. Confirm the changes by highlighting OK, then press Enter. …
  4. To save the changes and exit the BIOS Setup utility, press the F10 key.

How do I reinstall Windows 10 from BIOS?

Save your settings, reboot your computer and you should now be able to install Windows 10.

  1. Step 1 – Enter your computer’s BIOS. …
  2. Step 2 – Set your computer to boot from DVD or USB. …
  3. Step 3 – Choose the Windows 10 clean install option. …
  4. Step 4 – How to find your Windows 10 license key. …
  5. Step 5 – Select your hard disk or SSD.

1 мар. 2017 г.

How do I fix the aptio setup utility problem?

If you’re not sure how to reset BIOS settings, follow the instructions below:

  1. Restart your PC.
  2. The Aptio Setup Utility main menu should appear.
  3. Enter Settings and look for the ”Reset Configuration Data” or ”Factory reset” options.
  4. Reset BIOS to factory data and save changes.
  5. Exit Aptio and reboot your PC.

6 мар. 2019 г.

How do I fix insydeh20 setup utility?

14 Answers

  1. Start the machine and hit F2 to get to BIOS.
  2. Disable secure boot in the boot options screen.
  3. Enable the load legacy option ROM.
  4. Keep the boot list option set to UEFI.
  5. Press F10 to save and exit.
  6. Shut down the machine and start it again with the USB device attached.

9 мар. 2013 г.

How do I start aptio setup utility in Safe Mode?

Press the “F4” key to Enable “Safe Mode”. (The computer will then start in “Safe Mode” with a minimal set of drivers and services.)

Like this post? Please share to your friends:
OS Today