How do I get Windows to recognize a new SSD?
To get BIOS to detect the SSD, you need to configure the SSD settings in BIOS as follows:
- Restart your computer, and press the F2 key after the first screen.
- Press the Enter key to enter Config.
- Select Serial ATA and press Enter.
- Then you’ll see the SATA Controller Mode Option.
Why is my SSD not showing up when installing Windows 10?
If your SSD isn’t recognized by the BIOS when you attach it, check for these things: Check the SSD cable connection or switch another SATA cable. … Check if SATA port is enabled as sometimes the port is turned OFF in System Setup (BIOS). You may need to manually turn it on before you can see the drive in BIOS.
Why is my PC not detecting my new SSD?
The BIOS will not detect a SSD if the data cable is damaged or the connection is incorrect. Serial ATA cables, in particular, can sometimes fall out of their connection. … The easiest way to test a cable is to replace it with another cable. If the problem persists, then the cable was not the cause of the problem.
How do I activate Windows 10 on a new SSD?
To reactivate Windows 10 after a hardware change, use these steps:
- Open Settings.
- Click on Update & Security.
- Click on Activation.
- Under the “Windows” section, click the Troubleshoot option. …
- Click the I changed hardware on this device recently option. …
- Confirm your Microsoft account credentials (if applicable).
How do I initialize a new SSD?
In Windows 8 and later, move the mouse to the lower left corner of your desktop and right-click on the Start icon, then select Disk Management. When Disk Management opens, a pop-up will appear and prompt you to initialize the SSD. Select GUID partition table (GPT) and click OK.
How do I enable SSD in BIOS?
Solution 2: Configure the SSD settings in BIOS
- Restart your computer, and press the F2 key after the first screen.
- Press the Enter key to enter Config.
- Select Serial ATA and press Enter.
- Then you’ll see SATA Controller Mode Option. …
- Save your changes and restart your computer to enter BIOS.
How do I fix my SSD not detected?
Quick Fix. Unplug and Re-plug SATA Data Cable on SSD
- Unplug SATA data cable on SSD, leave the power cable connected.
- Turn on the PC and boot into BIOS.
- Let PC sit idle in BIOS for about half an hour and turn off PC.
- Plug the SATA data cable back into SSD and turn on PC to boot into BIOS.
Do I need to install Windows on my new SSD?
Nope, you should be good to go. If you have already installed windows on your HDD then no need to reinstall it . The SSD will get detected as a storage medium and then you can continue using it . But if you need windows on the ssd then you need to clone the hdd to the ssd or else reinstall windows on the ssd .
Where do you want to install Windows SSD not showing up?
Situation 1. SSD not recognized by BIOS
- Check the SSD cable connection. …
- Check if SATA port is enabled. …
- Connect the drive to another working computer to see if the SSD is damaged.
- Boot into BIOS, and set SATA to AHCI Mode. …
- If your SSD still is not showing at Windows Setup, press SHIFT+F10 to open a Command Prompt window.
How do I know if my SSD is installed correctly?
To find out if your SSD is installed properly, go into the UEFI menu of the mother board. Navigate to the installed devices section and if your SSD pops up you shop be fine!
Do I need to change BIOS settings for SSD?
For ordinary, SATA SSD, that’s all you need to do in BIOS. Just one advice not tied to SSDs only. Leave SSD as first BOOT device, just change to CD using fast BOOT choice (check your MB manual which F button is for that) so you don’t have to enter BIOS again after first part of windows installation and first reboot.
Can I use my Windows 10 key on a new SSD?
When you have a computer with a retail license of Windows 10, you can transfer the product key to a new device. You only have to remove the license from the previous machine and then apply the same key on the new computer.
Can I use the same product key to reinstall Windows 10 on SSD?
Yes, you can use the product key. When you upgraded from a previous version of Windows or receive a new computer preinstalled with Windows 10, what happened is the hardware (your PC) will get a digital entitlement, where a unique signature of the computer will be stored on Microsoft Activation Servers.
How do I activate Windows 10?
To activate Windows 10, you need a digital license or a product key. If you’re ready to activate, select Open Activation in Settings. Click Change product key to enter a Windows 10 product key. If Windows 10 was previously activated on your device, your copy of Windows 10 should be activated automatically.